All Categories

How to Install Pavers- Part 3

7/8/2016

Start laying the pavers along the longest straight side. Luckily, laying pavers is easy compared to all the work you've just done. Begin laying pavers at a 90-degree corner, preferably one that abuts the house or another structure, and continue extending the pavers along the longest straight side. Be sure to pull from several pallets of product in order to have a good blend of the colors. Pavers are made from natural materials that can cause slight changes to the appearance of the colored pavers. Working from several pallets will help to blend these slight differences into the surface. Work out from there, keeping your pavers in straight lines. Lay pavers by placing them straight down in the sand --do not slide them along the ground or kick them into place and disturb the sand. Slide each paver straight down the edge of the adjacent paver. Don't worry about gaps: you generally want to leave a 1/16" to 1/8" gap between pavers. Periodically check to make sure the pavers are flat, using a string to check each row for straightness.

Do not walk on your prepared sand. Stand on the pavers you have already installed and work your way out. Don't get too close to the edge of the pavers you've installed, or you might disturb the sand in front of them.

Cut pavers as needed. You'll almost invariably need to cut some pavers to fit the edges. Don't try to curve your pavers to fit the edging. Instead, lay all the whole pavers you can in each row and then go back and cut pavers to the correct sizes to fit the edge. Use a masonry saw or a guillotine-style splitter to make good, clean cuts. If you gave yourself plenty of pavers to work with in the beginning, you should have more than enough materials to accommodate even a few mistakes!

Once the pavers are all placed according to pattern, use a plate compactor to tamp the pavers into the sand. Once all the pavers are installed, run the plate compactor over them at least three times to ensure they are snugly pressed into the sand.

Be sure to use a protective covering over your plate compactor when you compress the pavers in order to avoid scuffing.

Seal your pavers. For added durability and lower maintenance, seal the pavers with an appropriate sealing product. Look for a non-toxic (vegetative safe) paver sealer, and don't forget to clean the pavers beforehand.

Sweep sand into the joints. Fill the joints between pavers with coarse sand like you used earlier, or use slightly finer sand. Pour it onto the pavers and sweep it into the cracks until they are completely filled. This sand "locks" the pavers in place. Make sure the sand is dry.

We have everything you need to complete this project here at Silt Tool Rental, including the pavers! Give us a call today! 970-876-5933

0 Comments

How to Install Pavers- Part 2

7/7/2016

1 Comment

Excavating the Space

Excavate the installation area. Spaces which will be exposed only to foot traffic generally need 4-6" of base material, while driveways or projects in very wet soil may need as much as 12" of base. Figure out how deep your base will need to be (consult Silt Tool Rental), and add about 1-1.5" for the sand layer, plus the thickness of the pavers (this varies by brand and style but is typically 2 3/8" or 3 1/8"). The sum of the depth of the base, the sand, and the pavers will be how deep you need to excavate your project area. Be sure to excavate 6-12" beyond the boundaries of the project to give you ample space to install your edge restraints.
Measure the depth of your excavation from the string you used to track your slope, not from the surface of the ground.

Choose your base material. Base material is usually coarse, crushed stone with sharp irregular edges. The two most important things about base material is that it remains strong when compacted (to serve as a base for your pavers) and that it drains properly. Poor structural integrity and poor drainage can ruin an otherwise perfect paving project.

Lay the base. Add no more than 6 inches (15.2 cm) at a time to the entire excavated area, and then compact with a hand tamper (for very small projects) or a mechanical plate compactor. It's essential that the base be well-compacted. Repeat this process until you have a base of the correct depth. Now is your last chance to properly adjust the height of the finished project and to ensure you don't have any dips or bumps. Slightly increase or decrease the thickness of the base as necessary, taking frequent measurements from your strings to the base.
Be sure to lay base material beyond the planned boundaries of the pavers. Laying the base outside the boundaries of the pavers will make your project more stable.
Continue adding base material and then compacting every 2 inches (5.1 cm) until you are about 3 inches (7.6 cm) from your desired finish height. When compacting, be sure to maintain a gentle slope — usually away from your house.

Install the edge restraints. Edge restraints will help hold the shape of your project over the years. Place these restraints, usually made of plastic, aluminum, or steel, around the perimeter of the project and secure them into the ground with 12" spikes. If your design is irregularly shaped, you'll need to cut the restraints in order to follow the edges of your design.

Put down a layer of sand. The sand is the material that holds your pavers in place. Use coarse sand and screed it smooth to a uniform depth of at least 1 inch (2.5 cm), but no more that 1 1/2 inches (5.1 cm). If your project is large, lay down 1" screed pipes and then pour the sand in between the pipes, screeding the sand in small sections (50-100 square feet each). Remove the pipes and then fill in the gaps with more sand.

1 Comment

How to Install Pavers- Part 1

7/6/2016

1 Comment

Make a plan. A good plan is essential to a successful paver project. Think about where you want your path, driveway, or patio, and then use graph paper to make a scaled drawing of the immediate area. Draw in your paver project. You'll have to play around with your design a bit, so be sure to use pencil and keep your drawing neat. Your project will need to have adequate drainage if you want it to be safe and durable. You'll also want to make sure that it slopes away from your house and other structures. To ensure adequate drainage, you should have a slope of at least 1/8" per linear foot (1/4" slope per linear foot is often recommended).

Check with your local utilities company before starting any construction. Installing pavers may be easy, but it's necessary to check with your local utilities company before beginning to ensure that you don't accidentally strike or obtrude any cables or pipes.

Order your materials. You have a lot of choices in the pavers you use. Most are brick or concrete, but you can find a variety of sizes, shapes, and colors. Find a style that is to your liking and that fits your budget either online or at your local builders supply store.
In general, if your project area isn't too irregularly shaped, you can safely calculate how many pavers you need by simply measuring the square footage of the footprint and adding 5%. If your design has a lot of curves, get an extra 10% over your best square footage estimate.
You should order a bit extra because you'll almost certainly end up having to cut some of the pavers to get the right fit. The fancier your outline, the more pavers you'll have to cut.

Outline the project area. Use string or garden hose to outline your project. Drive stakes to hold the outline in place and use a triangle to make clean corners.

Scope your slope. To avoid water pooling on your pavers, you want your pavers to be slightly above the surface of the surrounding ground at all points. Thus, when planning the slope, begin with what will be the highest point. Typically, this is the point at the bottom of the front door or otherwise closest to the house.
Drive a stake at the high point, and mark the correct height where the pavers will meet the door or structure. Tie a string around the stake at that height.
Drive a stake (if there isn't already one) at the outer boundary of your project. This will be your lowest point. Attach a line level to your string and then tie the loose end of the string around the outer stake at the height at which the line level tells you the entire string is level. Now from that line move down the stake at least 1/8" per linear foot (e.g. if it is 8 feet from your front door to the outer edge of your patio, move down the stake 1"), and draw a new line. Move your string down to this line. String cross-lines down the length of the project to ensure you mark the correct depth across the entire project.
If your project area has a variety of slopes, or if your design is irregular, you'll need to repeat this process in several points. It is absolutely critical that you get the slope right, so the more stakes, the better.

1 Comment

Star Precast Concrete Products Available at Silt Tool

6/10/2016

1 Comment

Interlocking Gecko Pavers

We are able to provide a vast array of items due to our special mold department. We have a large consumer population ranging from the general public buying for their landscaping needs, general contractors needing building materials, architects and engineers who need detailed architectural decorative pieces, and service providers who use concrete products because of the structural integrity and durability.

New innovative products are constantly being added to our product line. Expanding on our success in creating pre-cast concrete items, we are leaders in the development of recycled glass products being cast into decorative pieces with concrete derivatives.

We produce and manufacture all of our products in Parachute, Colorado. We have the ability to make virtually anything out of concrete due to our highly skilled staff and the latest technology.

1 Comment

Do you know About Silt Tool Rentals?

6/1/2016

1 Comment

Do you Know About Silt Tool Rentals?

Hidden in the sleepy town of Silt, Colorado is a little family owned and operated equipment sales and rental company.

Silt Tool Rental was started in March of 2012 by Lee & Terry Kirk of Silt Mesa. The original 5000 sq.ft. location, at 7th & Front Street, was outgrown within the year, as the customer base and equipment options grew. With the expanding business, it was soon realized that we would need to acquire a much larger property. Terry came across the perfect site, a ¾ acre lot at 135 River Frontage Road, South of I-70 and West of the Silt exit. This soon became home to the newly booming business. Three years later the expansion has continued.

Over the years we have acquired new locations, along with dealerships with such companies as BCS Equipment, Dolmar Chainsaws, Nifty Lift, Thunder Twist Bits & Cutting Tools and Weber. With the surrounding area growing as well, we saw an opportunity to broaden our horizons as far as sales and rentals. Just to name a few, we rent and sell a variety of Man Lifts, Skid Steers, Lawn/Garden Equipment, Heavy Equipment, Drywall, Construction and Party Rentals.

Along with sales and rentals, we also have an on-site mechanic. So if your lawn mower, chainsaw or any other equipment just isn’t operating as it should, give us a call. We’ll do our best to have you up and running in no time.

As a goal-achieving, service oriented business, we are always looking for ways to grow and strengthen our customer base. We're here for all of your equipment needs. We have tools for all of your home improvement projects and needs in one convenient place! Whether it be equipment, tools or trailers we have it, and if we don’t, we can get it. Our mission is to provide you, the customer with exactly what you need at a fair price. Customer Satisfaction is our Goal along with great customer service, reliable tools, and big smiles!

On your next project, big or small, look no further than Silt Tool Rental. Call Silt Tool Rentals for any of your projects needs! 970-876-5933

1 Comment

How to Install Pavers- Part 3

How to Install Pavers- Part 2

Excavating the Space

How to Install Pavers- Part 1

Check with your local utilities company before starting any construction. Installing pavers may be easy, but it's necessary to check with your local utilities company before beginning to ensure that you don't accidentally strike or obtrude any cables or pipes.

Star Precast Concrete Products Available at Silt Tool

Do you know About Silt Tool Rentals?

Do you Know About Silt Tool Rentals?

Author

Archives

Categories

Equipment for Sale

Equipment Rentals

About Us

Contact Us

Blog